Flashings

Flashings cover the joint between two different parts of the building - such as the join between the roof and the chimney. They sometimes act like gutters and carry a lot of water so dealing with leaks is important.

Where are flashings found?

Flashings can be found on many parts of your building.

A3 af.png

Replacing flashings

Flashings can be made from a number of materials:

  • lead is often the best material for flashings being flexible, capable of being welded and long lasting - a correctly installed lead flashing should last at least 60 years
  • zinc can also be welded but is less easy to shape - can last at least 30 years
  • bitumen compounds (“Nuralite”) have lasted for over 30 years however they do become brittle with age
  • mortar fillets may be used at the skew
  • polymer – a variety of trade products are available with life lengths from 20 - 30 years but some of them are nearly as expensive as lead

More about lead and alternative flashing materials 

Typical ways of constructing flashings

Mortar flashing

HES 14 2 cement fillet crop lite.jpg
Mortar fillet or flaunchingHistoric Environment ScotlandCracking is a common defect

These may also be called "fillets" or "flaunching" and are often used at the skew. A piece of wood called a "tilting fillet" is used to lift the edges of the slate so that water runs away from the join.   The joint is then covered with strong hydraulic lime mortar.

Keep an eye open for cracks and loose sections of mortar. 

F1 af.png

Lead Flashing to Skew

new lead flashing skew crop lite.jpg
Lead flashing to skewJohn GilbertNote the skew is low here so the flashing has been taken over the top of the stone to give sufficient depth

The flashing here forms a channel or "watergate". The drawing shows this made of lead but other materials can be used.  Note the edge of the lead is folded over on one side to stop capillary action taking water under the slates.  The edge by the skew has a cover flashing.

Valley Flashing

HES  18 crop lite.jpg

Used where two roof slopes meet at an angle, these are sometimes referred to as valley gutters.

F6.1 lead valley (2) af.png
Valley flashingJohn GilbertThe lead valley flashing is dressed over timber fillets to form a gutter. Laying the lead in sections and fixing the sections at the top only allows for expansion

Central Valley Flashing

skylight 0245 ccentral valley crop lite.jpg
Central valley gutter or flashingJohn Gilbert

These may have very wide flat bottoms and are often found on central valley roofs.  Otherwise, they are similar in construction to other types of lead flashing. where they are very wide, they should be formed like flat roofs.

Lead Bottle Flashing

tiled and slate roof side by side.jpg
Lead bottle flashingJohn Gilbert used here to join two types of roof

The drawing here shows a lead bottle flashing used to cover the join between a slate and tiled roof.   The lead is folded tight over a timber roll. Sides to the channel are made by folding the lead over strips of timber.  

F8 Lead bottle joint rev (2.png
Lead bottle flashingJohn GilbertThis type of joint is used to form a flashing between two different roof finishes. There is a lead gutter on each side of the raised 'bottle'

Problems

  • flashings can be lifted or torn by wind
  • lead flashings can be corroded by acid run off
  • incorrect laps or fixings
Wind Damage to Flashings   crop lite.jpg
Wind damage to flashingJohn Gilbert

Professional help recommended?

Although the work may appear straightforward, ensure your builder or tradespeople have the skills for the job. If in any doubt, get professional help to specify and organise the repair. Consider using a firm who is a member of the Lead Contractors Association or whose key workers have the appropriate qualifications.

P1050730 copy def flashing crop lite.jpg
Incorrectly laid lead flashingJohn GilbertLead has buckled with expansion

Who pays?

These are normally common or mutual repairs.

Further information

More information on lead and alternative materials 

More information on flat roofs

Historic Scotland Inform Guide 'Roofing Leadwork'